✂️ Diseña y Crea Sueter con Nudo Central ✂️// ✂️ Design and Create Center Knot Sweater ✂️

avatar

Hola queridos amigos de Hive. Quiero presentarles un diseño que he creado partiendo de un sueter base para realizar el diseño frontal.

Manos a la tijera!

Materiales:

  • 1 Sueter
  • Maquina de coser
  • Hilo
  • Tijera

PASO A PASO

1

Se toma el Sueter y la parte delantera de este se dobla justo a la mitad, asi como pueden observar en la imagen.

2


3
Se corta con la tijera justo a la mitad de la prenda.

Se divide en dos cuadrantes la prenda de manera que se coloca un alfiler en la zona central del sueter. Con la ayuda de la tijera se va a cortar una el sueter en forma de una curva, como pueden apreciar en la imagen.

4

Con la ayuda de la regla se va a visualizar esa area media del sueter, y exactamente en esa linea se va a cotar justo a al mitad.

5

Esta es la forma en la cual nos va a quedar la blusa. Luego se va a coser todos los bordes de la lineas que se han cortado con la tijera.

6

Luego se deben unir mediante costura la linea horozonal que separa la parte infeiror de la superior ( Es la linea punteada que pueden obeservar en la imagen) Se debe realizar esto en el lado derecho e izqierdo. El lado izquierdo Se debe coser gran parte de la linea horizontal dejando 5 cm y luego volviendo a coser para dejar un agujerito. Luego el lado derecho solo se debe coser y dejar 5 cm sin coser.

7

De esta manera quedaría un orificio del lado izquierdo y dos puntas del lado izquierdo.

Se procede a pasar la punta inferior derecha por ecima y hacia dentro del agujero del lado derecho de la prenda.

8

Luego se toma La punta superior izquierda de la prenda y se une a la punta inferior por el area interna del sueter y se fijan esta medianmte costura para formar el nudo central de la prenda.

Así, hemos terminado el diseño en esta oportunidad. Espero sus comentarios y recomendaciones! Saludos queridos Amigos!

Créditos:

  • Las imagenes son de mi autoria y fueron Tomadas a traves de un Telefono ZTE BLADE.

  • Traductor utilizado: Deepl

  • La edicion de las fotos la realicé mediante la aplicaciones Editor de Fotos Polish y los separadores se editaron en canva.


Hello dear friends of Hive. I want to present you a design I created starting from a base sweater to make the front design.

Hands to the scissors!

Materials:

  • 1 Sweater
  • Sewing machine
  • Thread
  • Scissors

STEP BY STEP

1

Take the sweater and fold the front part of it right in the middle, as you can see in the picture.

2

Cut with the scissors right in the middle of the garment.

3

The garment is divided in two quadrants so that a pin is placed in the central area of the sweater. With the help of the scissors the sweater is cut in the form of a curve, as you can see in the image.

4

With the help of the ruler you are going to visualize that middle area of the sweater, and exactly on that line you are going to stitch right in the middle.

5

This is the way the blouse is going to look. Then sew all the edges of the lines that have been cut with the scissors.

6

Then sew together the horizontal line that separates the bottom from the top (it is the dotted line that you can see in the picture). This should be done on the right and left side. On the left side you should sew a large part of the horizontal line leaving 5 cm and then sew again to leave a small hole. Then the right side should only be sewn and leave 5 cm unsewn.

7

This leaves one hole on the left side and two points on the left side.

Then pass the lower right point over and into the hole on the right side of the garment.

8

Then take the top left point of the garment and join it to the bottom point on the inside of the sweater and fasten it in the middle of the seam to form the central knot of the garment.

Thus, we have finished the design this time. I look forward to your comments and recommendations! Greetings dear friends!

Credits

  • The images are my own and were taken with a ZTE BLADE phone.

  • Translator utilization: Deepl

  • The editing of the photos was done using the Polish Photo Editor application and separators were edited in canva.



0
0
0.000
6 comments
avatar
Thank you for sharing this post in the DIYHUB Community!

Your content got selected by our fellow curator ashikstd & you just received a little thank you upvote from us for your great work! Your post will be featured in one of our recurring compilations which are aiming to offer you a stage to widen your audience within the DIY scene of Hive. Stay creative & HIVE ON!


Please vote for our hive witness <3

0
0
0.000
avatar

This post has been manually curated by @steemflow from Indiaunited community. Join us on our Discord Server.

Do you know that you can earn a passive income by delegating to @indiaunited. We share more than 100 % of the curation rewards with the delegators in the form of IUC tokens. HP delegators and IUC token holders also get upto 20% additional vote weight.

Here are some handy links for delegations: 100HP, 250HP, 500HP, 1000HP.

image.png

100% of the rewards from this comment goes to the curator for their manual curation efforts. Please encourage the curator @steemflow by upvoting this comment and support the community by voting the posts made by @indiaunited.

0
0
0.000