🌡️⚠️ Samsung S9 Plus with a charging issue. Temperature error. Solution // Móvil Samsung S9 plus con falla de carga. Error de temperatura. Solución🛠️✅

avatar

Greetings, community. A blessed day to all Hive readers.

Mis saludos comunidad. Bendecido día para todos los lectores de Hive.

Today has been a busy day at the workshop. We still have a few devices pending inspection for tomorrow. The ones that are disassembled are only there for inspection; their owners just want to know what is wrong with them.

Hoy ha sido un día atareado en el taller. Nos quedaron algunos aún pendientes de revisión para mañana. Los que están desmontados solo son para revisarlos; los propietarios solo quieren saber qué tienen.

Today, we will look at a Samsung S9 Plus that the customer tells us stopped charging. She connected it to an EcoFlow to charge, and it charged up to 40%, but the charging process did not go any further. We will carry out our initial diagnosis and then, if possible, proceed with the repair.

Veremos el caso hoy de un Samsung S9 Plus que la clienta nos refiere que dejó de cargar. Lo conectó a cargar en un EcoFlow y cargó hasta el 40%, pero de ahí no pasó la carga. Haremos nuestro diagnóstico inicial y luego, si es posible, la reparación.

DIAGNOSIS

DIAGNÓSTICO

1- The first thing we will do is connect the phone to the charger using our power supply as a tester. When we do this, an alert appears consisting of a yellow triangle and a thermometer. This is obviously a temperature warning, as if the phone were overheating, which we know is not the case because it is completely turned off and is not even warm.

1- Lo primero que haremos será conectar el móvil al cargador con nuestra fuente usándola como tester. Al hacerlo, nos salta una alerta que consiste en un triángulo amarillo y un termómetro. Esto es evidentemente una alerta de temperatura, como si el teléfono estuviera calentándose, algo que sabemos que no es, pues está totalmente apagado y no está ni siquiera tibio.

2- Now we will open our phone for an internal inspection. This model is relatively easy to open. We remove the SIM tray and, using something thin and hard, such as a blade, insert it through one corner until we can lift a small portion of the back cover. Then, through the lifted corner, we insert an X-ray film sheet and slowly slide it along. We can use isopropyl alcohol to loosen the adhesive a little. Once the back cover is removed, we unscrew and lift the NFC antenna, which also works as the wireless charging component.

2- Ahora abriremos nuestro teléfono para una revisión interna. Este modelo es relativamente fácil de abrir. Retiramos la bandeja porta SIM y, con algo fino y duro como una cuchilla, la introducimos por una esquina hasta poder levantar una pequeña porción de la tapa trasera. Luego, por la esquina levantada, introducimos una placa de radiografía y la vamos deslizando poco a poco. Podemos ayudarnos con alcohol isopropílico para aflojar un poco el pegamento. Una vez retirada la tapa trasera, destornillamos y levantamos la antena NFC, que también funciona como carga inalámbrica.

3- We have seen this behavior in other phones. This type of failure is associated with a thermistor related to the charging system, which is located precisely on the NFC and wireless charging antenna. When this thermistor becomes damaged and its resistance changes, this is precisely the symptom it causes. Normally, when it is in good condition, it should measure 100 kilo-ohms. So, we set our multimeter to diode mode and measure this thermistor. It gives us barely 1.1 ohms, so here we have found the fault and our final diagnosis: the thermistor associated with charging is damaged. It is completely out of specification.

3- Este comportamiento lo hemos visto en otros móviles. Este tipo de fallas está asociado a un termistor que se relaciona con la carga y que está precisamente en la antena NFC y la carga inalámbrica. Cuando este termistor se daña y cambia su resistencia, precisamente este es el síntoma que hace. Normalmente, cuando está en buen estado, debe medir 100 kiloohmios. Así que ponemos nuestro multímetro en escala de diodo y medimos este termistor. Nos da apenas 1.1 ohmios, así que aquí está la falla y nuestro diagnóstico final: termistor asociado a la carga está dañado. Totalmente fuera de parámetro.

REPAIR

> REPARACIÓN

1- Basically, what we need to do is replace this thermistor. However, we do not have that component. We will use an alternative solution. Since the thermistor is essentially a resistor whose resistance varies according to temperature, we will install a fixed resistor with the same value of 100 kilo-ohms. We will need to find one. We will measure components on an unused power bank board, which has many very small resistors, until we find one with this value. We found one measuring 98.7 kilo-ohms, which will work for us. We remove it from the board.

1- Básicamente, lo que debemos hacer es cambiar este termistor; sin embargo, no tenemos ese componente. Haremos una solución alternativa. Como el resistor es en sí una resistencia que varía su resistividad en función de la temperatura, colocaremos un resistor fijo con la misma medida de 100 kiloohmios. Tendremos que localizar uno. Mediremos en la placa de un power bank en desuso, que tiene cantidad de resistencias muy pequeñas, hasta encontrar una de esta medida. Localizamos una de 98,7 kiloohmios; esta nos servirá. La desmontamos de la placa.

2- Thermistors are generally extremely small in size. The resistor we found is almost three times larger than the original component, so we will not be able to install it in the same place. According to the schematic and parts diagram, we know that this thermistor is connected in series with pins 5 and 6 of the NFC connector. Therefore, we will solder a very thin wire to each side of the resistor and then solder one wire to pin 5 and the other to pin 6. After doing this, we remove the thermistor from the NFC antenna since it will no longer serve any purpose there.

2- Los termistores generalmente son de un tamaño extremadamente pequeño. La resistencia que hemos encontrado es casi del triple del tamaño del resistor; por ende, no podremos montarla en el mismo sitio. Por el plano esquemático y de partes, sabemos que este termistor está en serie con los pines 5 y 6 del conector NFC, así que soldaremos un cable muy delgado a cada lado de la resistencia y soldaremos uno al pin 5 y el otro al pin 6. Luego de hacerlo, desmontamos el termistor de la antena NFC, pues ya no surte efecto ahí.

3- Now we connect our battery and reconnect our USB cable. To our satisfaction, our Samsung S9 Plus has started charging. Quite satisfying! We assemble the device, and it is ready to be handed back to the customer.

3- Ahora conectamos nuestra batería, conectamos nuestro cable USB nuevamente y, para nuestra satisfacción, ya nuestro Samsung S9 Plus ha empezado a cargar. Algo gratificante. Armamos el equipo y listo para entregar al cliente.

We have seen these failures quite often in these Samsung high-end models from a few years ago. The S8, S8 Plus, S9, and S9 Plus frequently experience this type of problem, which is generally associated with irregularities in the charging process. Generic chargers and overvoltage can quickly damage this thermistor.

Estas fallas las hemos visto mucho en estos Samsung gama alta de hace unos años. El S8, S8 Plus, S9 y S9 Plus son muy frecuentes con estas fallas, que por lo general se asocian a irregularidades en la carga. Cargadores genéricos y sobrevoltajes dañan rápidamente este termistor.

This brings us to the end of this post. Thank you, readers, for your attention. If you have any questions, feel free to leave them in the comments. The images and text are entirely my own work.

Hasta aquí la presentación de este post. Gracias a los lectores por su atención. Cualquier duda pueden dejarla en los comentarios. Las imágenes y redacción son de mi total autoría.

Translated with the help of Google Translate.

Traducido con ayuda del traductor de Google.

See you soon.

Hasta pronto.



0
0
0.000
2 comments
avatar

Thanks for your contribution to the STEMsocial community. Feel free to join us on discord to get to know the rest of us!

Please consider delegating to the @stemsocial account (85% of the curation rewards are returned).

Thanks for including @stemsocial as a beneficiary of this post and your support for promoting science and education on Hive. 
 

0
0
0.000
avatar

Congratulations @multiingeniero! You have completed the following achievement on the Hive blockchain And have been rewarded with New badge(s)

You received more than 80000 upvotes.
Your next target is to reach 85000 upvotes.

You can view your badges on your board and compare yourself to others in the Ranking
If you no longer want to receive notifications, reply to this comment with the word STOP

0
0
0.000