Sustitución de carbonera a arranque de Corsa [ESP-ENG]

avatar

pixiz-15-06-2022-19-18-46.jpg

jghjhgjghj.png

Hola amigos, hace algunos días no los visitaba y mi conciencia me decía que tenía una deuda con mi apreciada comunidad de hivemotors ☺️. Así que hoy les traigo un trabajo que realizó mi esposo a un arranque de Corsa. Anteriormente quizás tuvieron la oportunidad de ver en una de mis publicaciones el cambio de una carbonera de un arranque. Aunque tengan la misma función en todos los vehículos, debo mencionarles que no todos los arranques son iguales ni del mismo tamaño.

A diferencia del arranque de una camión este arranque de Corsa es mucho más pequeño, el automático es diferente y la carbonera también. Y si les soy sincera es de menos complejidad creo que ya lo haría 👍.

Este arranque también tiene dos tornillos largo los cuales hay que extraerlos con un dado, existen otros dos tornillos en la tapa superior y se deben quitar con un destornillador de estría. Seguido de esto, con una llave pequeña quitar el cable que va de la carbonera al automático.

Hello friends, it's been a few days since I visited you and my conscience was telling me that I owed a debt to my appreciated community of hivemotors ☺️. So today I bring you a job my husband did to a Corsa starter. Previously you may have had the opportunity to see in one of my posts the replacement of a carburetor on a starter. Although they have the same function on all vehicles, I should mention that not all starters are the same or the same size.

Unlike a truck starter, this Corsa starter is much smaller, the automatic is different and so is the carburetor. And if I'm honest it's less complex I think I would do it already 👍.

This starter also has two long screws which must be removed with a die, there are two other screws on the top cover and must be removed with a slotted screwdriver. After this, with a small wrench remove the cable that goes from the coal bunker to the automatic.

IMG_20220613_135903.jpgIMG_20220613_133000.jpg
IMG_20220613_133447.jpgIMG_20220613_133105~2.jpg

Luego de extraer la carbonera, sacamos el inducido para hacerle limpieza en la parte donde van contestados los carbones, para que de esta manera la nueva carbonera haga el contacto requerido en el inducido. Para esto se usó un papel de lija fina.

After extracting the coal bunker, we took out the armature to clean the part where the coals are placed, so that the new coal bunker would make the required contact with the armature. For this we used a fine sandpaper.

IMG_20220613_133747.jpgIMG_20220613_133756.jpg

IMG_20220613_134021.jpg

Ya se comienza a armar, pero primero se tuvo que quitar el automático, pues éste modelo cuánta con una pieza interna que se ajusta al inducido y esa debe encajar (en unas de las siguientes fotografías la señalaré con el dedo).

The assembly has already begun, but first the automatic had to be removed, because this model has an internal piece that fits the armature and that must fit (in one of the following pictures I will point it out with my finger).

IMG_20220613_134538~2.jpg

IMG_20220613_134829.jpg

Luego de haber colocado el inducido, tambien. Se ajusta el automático. Luego se procedió a colocar la nueva carbonera. Particularmente me llamo la atención de la carbonera nueva que trae un plástico que facilita la instalación. Antes de concluir el trabajo y de armar completamente se le coloco grasa en la punta superior. Ahora sí queda armar el resto, sin olvidar colocar el cable de la carbonera en el automático.

After having placed the armature, too. The automatic is adjusted.
Then we proceeded to place the new carbonera. Particularly I called my attention to the new coal bunker that brings a plastic that facilitates the installation. Before concluding the work and assembling it completely, I put grease on the upper end. Now it remains to assemble the rest, without forgetting to place the cable of the coal bunker in the automatic.

IMG_20220613_133610.jpgIMG_20220613_135322~2.jpg
IMG_20220613_135322~2.jpgIMG_20220613_135755.jpg

IMG_20220613_135407.jpg

Hasta aquí el trabajo realizado amigos mecánicos, espero que le sea de utilidad. Bueno para quienes como yo somos aprendices.

Hasta una próxima. 👋

So far the work done mechanical friends, I hope you find it useful. Good for those who like me are apprentices.

See you next time. 👋

jghjhgjghj.png


Las fotos son de mi propiedad te mandas con mi teléfono Alcatel

Photos are my property you send with my Alcatel phone.

Foto de portada editada por mi con la aplicación pixiz.com

Cover photo edited by me with pixiz.com application

Está publicación fue traducida en DeepL

This publication was translated at DeepL

Separador usado de Pixabay



0
0
0.000
7 comments
avatar

Watch out for the human traffickers at hivefest. You wont know it until its too late. STAY AWAY! Beware, traffickers can be women or men! They will act nice until they dont. There is human trafficking going on around this type of crypto. I have witnessed it. They literally have attempted my murder and are trying to kill me with V2K and RNM. Five years this has been happening to me, it started here, around people that are still here. Homeland security has done nothing at all, they are not here to protect us. Dont we pay them to stop shit like this? The NSA, CIA, FBI, Police and our Government has done nothing. Just like they did with the Havana Syndrome, nothing. Patriot Act my ass. The American government is completely incompetent. The NSA should be taken over by the military and contained Immediately for investigation. I bet we can get to the sources of V2K and RNM then. https://ecency.com/fyrstikken/@fairandbalanced/i-am-the-only-motherfucker-on-the-internet-pointing-to-a-direct-source-for-voice-to-skull-electronic-terrorism ..... https://ecency.com/gangstalking/@acousticpulses/electronic-terrorism-and-gaslighting--if-you-downvote-this-post-you-are-part-of-the-problem if you run into one of them you may want to immediately shoot them in the face. 187, annihilate, asphyxiate, assassinate, behead, bleed, bludgeon, boil, bomb, bone, burn, bury, butcher, cap, casket, choke, chop, club, crucify, crush, curb, decapitate, decimate, deflesh, demolish, destroy, devein, disembowel, dismember, drown, electrocute, eliminate, end, euthanize, eviscerate, execute, explode, exterminate, extinguish, finish, fry, grind, guillotine, gut, hack, hang, hit, ice, implode, incinerate, kill, liquidate, lynch, massacre, maul, microwave, mutilate, neutralize, obliterate, off, pop, poison, punnish, quarter, ruin, shank, shock, shoot, shred, skin, slay, slaughter, smoke, smother, snipe, snuff, squish, stab, strangle, stone, suffocate, suicide, SWAT, swing, terminate, torture, terrorize, whack, waste, wreck. You better fucking kill me.

0
0
0.000
avatar

Congratulations @rigel-gladys! You have completed the following achievement on the Hive blockchain and have been rewarded with new badge(s):

You distributed more than 100 upvotes.
Your next target is to reach 200 upvotes.

You can view your badges on your board and compare yourself to others in the Ranking
If you no longer want to receive notifications, reply to this comment with the word STOP

To support your work, I also upvoted your post!

Support the HiveBuzz project. Vote for our proposal!
0
0
0.000
avatar

Hola Rigel, bueno yo tuve un Corsa 1.4, dos puertas y algunos camiones. Es cierto ese que dices sobre los arranques, pues aunque tienen la misma función las piezas son diferentes.

Gracias por compartir con nosotros.
También es importante recalcar, que siempre que lo requiera, debemos hacerle una limpieza o mantenimiento, ya que si se daña es triste y peor y estás en la carretera.

0
0
0.000
avatar

Hola amigo muchas gracias por dejar su comentario, para mí es importante. Cierto aunque algunos trabajos de mecánica nos parezca sin importancia no lo son porque se debe incluir su debido mantenimiento, como mencionas tener un carro en carretera en condiciones dudosas puede ocasionar molestias u otras situaciones desagradable. Mil gracias por dejar su comentario. Saludos. Hasta pronto

0
0
0.000
avatar

¡Enhorabuena!


Has recibido el voto de PROYECTO CHESS BROTHERS

✅ Has hecho un buen trabajo, por lo cual tu publicación ha sido valorada y ha recibido el apoyo de parte de CHESS BROTHERS ♔ 💪


♟ Te invitamos a usar nuestra etiqueta #chessbrothers y a que aprendas más sobre nosotros.

♟♟ También puedes contactarnos en nuestro servidor de Discord y promocionar allí tus publicaciones.

♟♟♟ Considera unirte a nuestro trail de curación para que trabajemos en equipo y recibas recompensas automáticamente.

♞♟ Echa un vistazo a nuestra cuenta @chessbrotherspro para que te informes sobre el proceso de curación llevado a diario por nuestro equipo.


Cordialmente

El equipo de CHESS BROTHERS

0
0
0.000
avatar

Me encanta como te defines como aprendiz tras observar como reparan las piezas en persona, todos deberíamos aprender al menos lo básico sobre nuestros vehículos y como funcionan para saber cuando y como se da alguna falla y mas aun, identificar su nivel de gravedad para decidir si debe ser reparada de manera inmediata, me disculpo por mi tardanza en leerlo, gracias por publicar, espero leerte de nuevo pronto :)

0
0
0.000
avatar

Gracias amigo Jesús por dejar tu comentario. Si, debo no solo aprovechar los trabajos de mecánica para compartir con mis amigos de Hive, sino que también para que me quede como aprendizaje . Saludos 👋

0
0
0.000