Curious repair Aiwa CX-LX7U [Eng+Spa]

avatar


English



Greetings to all, very happy to be sharing once again with you. I promised to post more often in this community and little by little I'm on it.

This time it is a repair that I have been working on, it is not in itself a very old equipment, as I usually do. Surely it will seem a bit strange repair, I warn you now. Even so, it is really simple and entertaining.

The equipment in question is an Aiwa model CX-LX7U, this equipment came into my hands from a good friend that I respect and admire a lot. That he was kind enough to put it at my disposal and without hesitation I took it (he is an Aiwa).

The connections for the horns or loudspeakers were damaged, but I made the change before thinking of writing about it (the green circle), so I didn't take pictures of the process, sorry for that. The interesting thing about the matter is that when I connected it to the electrical outlet I could not turn it on.

It is not the first time that I come across a device that was saved at some point, without malfunctioning, and at the time when it comes to turning it on it does not work. It is the strange and common case, that a piece of equipment is damaged without using it in storage, which worked well.

For the explanation of the general work method that I apply in the service and to put them a little in context, I will comment now: When I studied and did my internship I worked in a company in which the specialists were German, they are very methodical and efficient people.



Image's Source - Fuente de la Imagen


I learned and got used to following a logical sequence of steps to repair equipment and, if possible, trying to understand what caused the failure. In order to have a plan with the idea of ​​repairing it before it happens. (which in other companies in which I work around here, is considered crazy)

So following the sequence of steps I started with the basics in all repairs: the power cable and connector, which was of very good quality.

I disassembled the equipment and followed the cable to the part where it reaches the power supply, the welds are not cracked, the failure of the welds is a more common fault than you can imagine.

Connect the appliance outlet to the breadboard with the short circuit detector, nothing is present and I have the proper voltage.



Image's Source - Image Source



So now I must continue with the output of the source, measure that the connections of the equipment are not crossed and prevent turning on the equipment and all the ordered sequence of steps.



Image's Source - Fuente de la Imagen


But something happens that I don't know if it's common from where you can read me: after you have about ten years or more having experience doing a job, in some way you develop an instinct, let's say, to call it in some way. Or some kind of inner voice, I don't know how to explain it really.



Image's Source

It is as if the device itself indicated the fault, and it is something that collides a bit with my methodical and orderly way of working. And when I get ready to continue disassembling to find the fault, that feeling is there, and naturally, but automatically, without reasoning, I find myself adjusting the 401 connector, for no reason.

The fact is that later I try the equipment and it turns on without problems, it has been one of the simplest repairs in my workshop. I have to test the record player for a few hours to make sure I can move another piece of equipment to the workbench to repair or restore.

For now, I apply the wash with alcohol and a brush to improve the appearance.

I thought it would be a longer and more laborious job, but it really wasn't complicated at all, it's more of a mysterious anecdote.

Thank you very much for stopping by and reading me on this curious repair.

I have used google translate for english language.
The images unless indicated are captures taken in my workshop.

Have a very good rest and that next week be full of encouragement and will to challenge the challenges that life has prepared for us.

Peace everyone.



Español



Saludos a todos, muy feliz de estar compartiendo una vez más con ustedes. Prometí publicar más seguido en esta comunidad y poco a poco estoy en ello.

Esta vez es una reparación que en la que he estado trabajando, no es en sí un equipo muy antiguo, como suelo hacer. De seguro que les parecerá que es una reparación un poco extraña, les advierto desde ahora. Aun así, es realmente sencillo y entretenido.

El equipo en cuestión es un Aiwa modelo CX-LX7U, este equipo llego a mis manos de parte de un buen amigo que respeto y admiro mucho. Que tuvo la amabilidad de ponerlo a mi disposición y sin dudarlo lo tome (es un Aiwa).

Las conexiones para las cornetas o altoparlantes estaba deteriorada, pero hice el cambio antes de pensar en escribir sobre el tema (el círculo verde), así que no tome imágenes del proceso, disculpen por ello. Lo interesante del asunto es que al conectarlo a la toma eléctrica no pude encenderlo.

No es la primera vez que me encuentro con un artefacto que se guardó en algún momento, sin tener fallas de funcionamiento, y al tiempo cuando se trata de encenderlo no funciona. Es el extraño y común caso, de que se daña un equipo sin usarlo almacenado, que funcionaba bien.

Para la explicación del método de trabajo general que aplico en el servicio y ponerlos un poco en contexto, les comentaré ahora: Cuando estudie e hice mi pasantía trabaje en una compañía en que los especialistas eran alemanes, son gente muy metódica y eficaces.



Image's Source - Fuente de la Imagen


Aprendí y me acostumbré con ellos a seguir una secuencia lógica de pasos para reparar equipos y en lo posible a tratar de entender que origino la falla. Para así tener un plan con la idea de repararla antes de que suceda. (lo que en otras empresas en que trabaje por aquí, se considera descabellado)

Así que siguiendo la secuencia de pasos comencé por lo básico en todas las reparaciones: el cable y el conector de alimentación eléctrica, que era de muy buena calidad.

Desarme el equipo y seguí el cable hasta la parte en que llega a la fuente de alimentación, las soldaduras no están agrietadas, que falle las soldaduras es una falla más común de lo que se pueden imaginar.

Conecte la toma de corriente del aparato al tablero de pruebas con el detector de corto circuito, sin ninguna novedad presente y tengo el voltaje apropiado.



Image's Source - Fuente de la Imagen



Así que ahora debo seguir con la salida de la fuente, medir que las conexiones del equipo no estén cruzadas e impidan encender el equipo y toda la secuencia ordenada de pasos.



Image's Source - Fuente de la Imagen


Pero sucede algo que no sé si es común desde donde me pueden leer: después de que tienes unos diez años o más teniendo experiencia haciendo un trabajo, de alguna forma desarrollas un digamos instinto, por llamarlo de alguna manera. O una especie de voz interna, no sé cómo explicarlo en verdad.



Image's Source - Fuente de la Imagen

Es como si el mismo aparato te indicase la falla, y es algo que choca un poco con mi manera metódica y ordenada de trabajar. Y cuando me dispongo a seguir desarmando para encontrar la falla, está ese sentir allí, y de forma natural, pero automática, sin razonar, me encuentro ajustando el conector 401, sin ningún motivo.

El caso es que luego pruebo el equipo y enciende sin problemas, ha sido una de las reparaciones más sencillas de mi taller. Tengo que probar unas horas el reproductor de discos para asegurarme de poder pasar a la mesa de trabajo otro equipo a reparar o restaurar.

Por ahora, aplico el lavado con alcohol y un cepillo para mejorar la apariencia.

Creí que sería un trabajo más largo y laborioso, pero realmente no fue nada complicado, es más bien una anécdota misteriosa.

Muchas gracias por pasar y leerme en esta reparación tan curiosa.

He usado el traductor de Google para el idioma inglés.
Las imágenes a menos que se indique son capturas tomadas en mi taller.

Que tengan un muy buen descanso y que la próxima semana estén llenos de ánimo y voluntad para desafiar los retos que nos tenga preparada la vida.

Paz a todos.



0
0
0.000
7 comments
avatar

This post has been manually curated by @bhattg from Indiaunited community. Join us on our Discord Server.

Do you know that you can earn a passive income by delegating to @indiaunited. We share 100 % of the curation rewards with the delegators.

Here are some handy links for delegations: 100HP, 250HP, 500HP, 1000HP.

Read our latest announcement post to get more information.

image.png

Please contribute to the community by upvoting this comment and posts made by @indiaunited.

0
0
0.000
avatar

My good friends, thank you for stopping by and supporting me.

0
0
0.000
avatar

Good work. Repair of such old devices can not be a easy task. And it is very good to bring them back to life.

0
0
0.000
avatar

If it is one of those rare pleasures that life gives us, sometimes I get more difficult cases. But reviving them gives me great satisfaction.

Thanks for stopping by and leaving your comment.

0
0
0.000