Diy Cover for Coffee Thermos / Diy Funda para Termo de Café

avatar

Diy Coffee Thermos Cover
.

As every coffee addict, specifically latte, I always like to take the one I make myself wherever I go, so I always have a Thermo for my hot drink. Currently, you get many models, size, designs and colors in the market, I had a gray one (the one you can see in the next picture on the right side) and it deteriorated in what is the metal part by the use, and this made me feel very bad because it really is very good inside, but its exterior part I don't like anymore.

This weekend I fell in love with a Termo in black with gold details, and based on my experience I understand that it must be protected from the beginning. Today I present to you a Diy Coffee Thermos Cover, which I made in accordance with the colors it has and I really liked it. Below I show you:

Diy Funda para Termo de Café

Como toda adicta al café, específicamente al café con leche, siempre me gusta llevar el hecho por mí misma a donde vaya, de manera que siempre tengo un Termo para mi bebida caliente. Actualmente, se consiguen muchos modelos, tamaño, diseños y colores en el mercado, yo tenía uno de color gris (el que se aprecia en la siguiente foto del lado derecho) y se deterioró en lo que es la parte metálica por el uso, y esto me hizo sentir muy mal porque realmente está muy bien por dentro, pero su parte exterior ya no me gusta.

Este fin de semana me enamoré de un Termo de color negro con unos detalles en dorado, y basada en mi experiencia entiendo que hay que protegerlo desde el principio. El día de hoy les presento un Diy Funda para Termo de Café, el cual hice en concordancia con los colores que tiene y me gustó muchísimo. A continuación te muestro:

)

The materials are very few, and even more so because the design I thought of for this case, is only to protect the metal part, since the top part is plastic and does not deteriorate as much, plus it has a system to open and take, which I did not want to be interrupted by having to open the case to access my coffee.

Los materiales son muy pocos, y más aún porque el diseño que pensé para esta Funda, es solo para proteger la parte metálica, ya que la parte de arriba es de plástico y no se deteriora tanto, además de que tiene un sistema para abrirse y tomar, el cual no quería que se viera interrumpido por tener que abrir la funda para acceder a mi café.

  • Sky Canvas
  • Printed fabric
  • Chain
  • Sewing machine, needle and thread
  • Pins, paper clips and scissors.
  • Ruler, pen, tape measure, compass and sheet.
  • Loneta sky
  • Tela Estampada
  • Cadena
  • Máquina de coser, aguja e hilo
  • Alfileres, clips de presión y tijera
  • Regla, bolígrafo, cinta métrica, compás y hoja.


First with the tape measure I measure the perimeter of my thermos, which will determine the body of the cover. In this case it was 24 cms since I considered a seam allowance and a clearance for the thermos to fit easily **This measurement is important, since I will use it to calculate the exact base of this cover **.

I also measure the height of the cover from the base to the top before the lid and considering the seam allowance I got 18 cm.

Primero con la cinta métrica tomo la medida del perímetro de mi termo, la cual determinará el cuerpo de la funda. En este caso dio 24 cms ya que consideré un margen de costura y una holgura para que el termo entre fácilmente.Esta medida es importante, ya que la usaré para calcular la base exacta de esta funda.

También mido el alto de la funda que desde la base hasta arriba antes de la tapa y considerando los márgenes de costura me dio 18 cms.

To calculate the base of the Case, I will do it Without Pattern, I will use the support of Mathematics, with the value of PI (3,14)
.

To make the Base of the Case which is a circle and that this will be perfectly in the measure of the width of the piece of the body of the Case when sewing it, I use the following mathematical formula, it is very simple:

The measurement around the thermos that I took previously and that gave 24 cms, I divide it by the PI Number which is 3.14. This gives 7.64 and I approximate it to 8, being then of value 8 cms which would be the diameter of the circumference of the base.

Para calcular la base de la Funda, lo haré Sin Patrón, usaré el apoyo de las Matemáticas, con el valor de PI (3,14)

Para hacer la Base de la Funda que es un círculo y que éste quedé perfectamente en la medida del ancho de la pieza del cuerpo de la Funda al coserlo, uso la siguiente fórmula matemática, es muy sencilla:

La medida del alrededor del termo que tomé anteriormente y que dio 24 cms, lo divido entre el Número PI que es 3,14. Esto da 7,64 y lo aproximo a 8, siendo entonces este de valor 8 cms lo que sería el diámetro de la circunferencia de la base

Then, I make a straight line of 8 cms that is the Base Diameter and with a compass I stop in the middle of that measure that would be 4cms and I take the tip of the compass to the 8cms and Listo I trace my Circumference that will be the Exact Base of the Cover and when I sew both pieces neither will be left over nor will anything be missing, so we have made the Pattern of this Design ❤️❤️ This base I cut it or circumference I cut it once in sky canvas and once in the printed fabric.

.

Note 📢📢 The formula I just used is this:


.

Perimeter / PI = Diameter.

That was too easy and thanks to Mathematics we can make our own patterns, which are accurate..

Entonces, hago una recta de 8 cms que es el Diámetro de la Base y con un compás me paro en la mitad de esa medida que sería 4cms y llevo la punta del compás hasta el 8cms y Listo trazo mi Circunferencia que será la Base exacta de la Funda y cuando cosa ambas piezas ni sobrará ni faltará nada, de manera que hemos realizado el Patrón de este Diseño ❤️❤️ Esta base la corto o circunferencia la corto una vez en loneta sky y una vez en la tela estampada.

.
Nota 📢📢 La fórmula que acabo de usar es está:

.

Perímetro / PI = Diámetro

Eso fue demasiado fácil y gracias a las Matemáticas podemos hacer nuestros propios patrones, que sean exactos.

Now with the measurements that I took previously of the body of the thermos and that gave 24 cms by 18 cms, I cut once in sky canvas and once in the printed fabric. I place front to front and sew on one of the lengths with a straight seam.

Ahora con las medidas que tomé anteriormente del cuerpo del termo y que dio 24 cms por 18 cms, corto una vez en loneta sky y una vez en la tela estampada. Coloco frente con frente y coso en uno de los largos con costura recta.

I open the piece and I'm going to make a repise but considering that there is a margin of the black sky canvas, to make sure that the design on the outside is not going to see any of the lining, which is the printed fabric. Then I pin and sew.

Abro la pieza y voy a realizar un repise pero considerando que quede un margen de la loneta sky de color negro, para asegurarme que el diseño en su parte externa no se vaya a ver nada del forro que es la tela estampada. Entonces fijo con alfileres y coso.

I fold in half and cut with the scissors to obtain two equal pieces.

Doblo por la mitad y corto con la tijera para obtener dos piezas iguales.

The remains of the lotena sky I used them to make two strips, with a piece of 6 cm x 2 cm, I fold it meeting in the center and then fold it again. I sew by machine and do the same to obtain two strips.

Los restos de la lotena sky los aproveché para hacer dos tiras, con una pieza de 6 cms x 2 cms, la doble encontrándose en el centro y luego doblo nuevamente. Coso a máquina y hago lo mismo para obtener dos tiras.

Now I place the pieces I have prepared facing each other, and mark a distance of 3 cm at the top where I will place the strip in the form of a ring, and sew that end.

Ahora coloco frente con frente las piezas que he preparado, y marco una distancia en la parte superior de 3 cms donde colocaré la tira en forma de aro, y coso todo ese extremo.

I clean up the edge with the scissors and zig zag stitch to secure and to prevent the fabric from opening.

Limpio el borde con la tijera y paso una costura de zig zag para asegurar y para que no se abra la tela.

The base in sky canvas, I fold it in half to mark with small cuts the halves or halves.

La base en loneta sky, la doblo por la mitad para marcar con pequeños cortes los medios o mitades.

I also fold the prepared body piece in half and mark it. I although I am absolutely certain that the body piece of the case is going to match its base perfectly, I always take the precaution of doing a basta type hand stitch to see for myself.
Below you can see that this Pattern has been a SUCCESS everything matched exactly ❤️❤️

La pieza del cuerpo que está preparada también la doblo por la mitad y marco. Yo aunque tengo la absoluta certeza de que la pieza del cuerpo de la funda va a coincidir perfectamente con su base, siempre tomo la precaución de hacer una costura a mano tipo basta para verlo con mis propios ojos.
A continuación puedes ver que este Patrón ha sido un Éxito todo cuadró exacto ❤️❤️

Now that you are sure of everything, attach the base with its lining to the body of the cover, using the sewing machine with a straight seam and then zig zag. You can see how perfect it all came together, neither too much nor too little.

Ahora ya segura de todo, su uno la base con su forro al cuerpo de la funda, usando la máquina de coser con costura recta y luego zig zag. Ve que perfecto quedó todo unido, ni sobró ni faltó.

Now I flip the piece to the right.

Ahora volteo la pieza al derecho.

All that remains is to place the 28 cm chain on the rings that we sewed.

Solo queda colocar la cadena que 28 cms en las aros que cosimos.

I loved the whole design and finish. The printed fabric lining adds a lot of interest, looks very cute and chic.

Me encantó todo el diseño y los acabados. El forro en tela estampada le aporta mucho interés, se ve muy lindo y chic.

The chain I used is golden and it matches perfectly with the design of the thermos, it adds shine and the contrast with the black is fabulous.

La cadena que usé es dorada y combina perfecto con el diseño del termo, le aporta brillo y el contraste con el negro es fabuloso.

As I told you before, the design I thought of for this case, was so that it does not cover the top, and in this way it does not interrupt its operation.
This way it is very easy to open and take naturally.

Como les dije anteriormente, el diseño que pensé para esta funda, era para que no tapara la parte superior, y de esta forma no interrumpe su funcionamiento.
De esta forma es muy fácil de abrir y tomar naturalmente.

This Case for my Coffee Thermos is not only functional, it's a great accessory that can match our keychain or other things I'll think of.

Esta Funda para mi Termo de Café no solo es funcional, es un gran accesorio que puede hacer juego con nuestro llavero u otras cosas que ya pensaré.

Well, mission accomplished... This thermos will be protected and will last beautiful for a long time. I'm even thinking that the previous gray thermos I'm also going to make its cover to extend its useful life and make it look nicer because it's still fully operational.

Bueno, misión cumplida... Este termo estará protegido y durará bello por mucho tiempo. Incluso estoy pensando que el termo anterior de color gris también voy a hacer su funda para extender su vida útil y que se vea más lindo porque está totalmente operativo aún.

I hope you liked this Tutorial. If you liked it I thank you for liking and sharing it so that other people can also do it and take care of their articles.

A hug and I cordially invite you to my next publication.

Deseo que les haya gustado este Tutorial. Si te gusto te agradezco tu Me gusta y que compartas para que otras personas también puedan hacerlo y cuidar sus artículos.

Un abrazo y los invito cordialmente a mi próxima Publicación...

---------- ❤️❤️❤️❤️ ----------

I took the photos with my Redmi Note 8
Apps I used:
Blend for the Cover
Inshot for the photos
Deepl Translate

My social networks:
Discord: YennysYaneth#0189
Twitter: @yennysferm
Instagram: @yennysyaneth

---------- ❤️❤️❤️❤️ ----------

Las fotos las tomé con mi Redmi Note 8
Apps que usé:
Blend para la portada
Inshop para los Collages
Deepl como Traductor

Mi redes sociales:
Discord: YennysYaneth#0189
Twitter: @yennysferm
Instagram: @yennysyaneth



0
0
0.000
16 comments
avatar

Necesario y muy útil este forro. Además está precioso. Como siempre en tus post muy bien detallados los pasos para elaborarlos. Muchas gracias 😉👆🤗

0
0
0.000
avatar

¡Me encantó! Yo no llevo café pero si agua y esta funda me serviría totalmente para esos días que no llevo un bolso grande 😌, es una idea genial, muchas gracias por compartirla 💖.

0
0
0.000
avatar

Una idea genial amiga refelicito me encantó
💯🎉❤️🌼🤗👏🌺🙌🙌🌺🤗🌼❤️🎉😍😘🌹🌟🌸✨🙌🙌🤩👏🌼😍😘☺️🌸🥰🙌🤩❤️👍😘☺️🌸🌺🌺🤗🎉💯🎉🌼👏

0
0
0.000
avatar

Gracias amiga por tu comentario. Ojalá se me hubiese ocurrido antes con el termo gris q se deterioró tan rápido. Hay q proteger las cosas cuando están bien...

Un abrazo 🤗🤗

0
0
0.000
avatar

Que gran idea amiga!✨
Siempre me sorprende los trabajos tan hermosos que haces , siempre un trabajo muy limpio , delicado y tus post siempre ordenados.

Gracias por compartir amiga, Saludos ✨😊

0
0
0.000
avatar

Hermoso y muy útil la funda que diseñaste.
Muchas gracias por compartir tu trabajo.
Saludos.

0
0
0.000
avatar

Gracias @elmundodebetty admiro mucho tu trabajo, y me hace muy feliz tu comentario

Es bueno cuidar y proteger las cosas apenas las compramos... Un abrazo 🤗🤗

0
0
0.000
avatar

No me gusta el café, pero me encantan las bebidas frías, me gusta mucho el estampado de la tela está muy lindo este trabajo ✨🌺💗

0
0
0.000
avatar

Gracias amiga. Este proyecto gustó mucho xq todos necesitamos una funda para nuestra bebida preferida, bien sea para proteger, transportar, ocultar o como accesorio.

Saludos 🤗🤗

0
0
0.000
avatar

Parece como si fuera un accesorio del mismo termo, le felicito, ha sido un trabajo ingenioso y muy bueno.

0
0
0.000